BJPMG - VARGLAS SILICONE RUBBER SLEEVING
- MSDS: BJPMG
- Manufacturer: VARFLEX CORP
- Product Name: VARGLAS SILICONE RUBBER SLEEVING
- National Stock Number: 5970-00-827-2515
Product Identification
Product ID:VARGLAS SILICONE RUBBER SLEEVING
MSDS Date:04/27/1989
FSC:5970
NIIN:00-827-2515
MSDS Number: BJPMG
Responsible Party
ROME, NY 13440
US
Emergency Phone: 315-336-4400
Info Phone: 315-336-4400
Cage: 79074
Contractor
Telephone: 315-336-4400
Cage: 79074
Ingredients
FIBERGLASS-SIO*2, NA*2CO*3, CAO
Fraction By Weight: N.A.
OSHA PEL 15 MG/M3(TOTAL DUST)
ACGIH TLV: 10 MG/M3 (DUST)
SILICONE RUBBER-VINYL, METHYL & PHENYL
Fraction By Weight: N.A.
Hazards
Routes of Entry: Inhalation:NO Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:YES
Health Hazards Acute and Chronic:ACUTE: SKIN-TRANSIENT MECHANICAL
IRRITATION. EYE-DIRECT CONTACT WILL CAUSE MECHANICAL IRRITATION.
INGEST-UNLIKELY TO OCCUR. CHRONIC: SKIN-NONE. EYE-NONE.
INGEST-NONE.
Explanation of Carcinogenicity:NO EXPLANATORY NOTE OR ADDITIONAL
INFORMATION SUPPLIED BY MANUFACTURER ON CARCINOGENITY.
Effects of Overexposure:OBSERVE INDIVIDUAL. IF SYMPTOMS DEVELOP,
CONSULT PHYSICIAN.
Medical Cond Aggravated by Exposure:SKIN PROBLEMS.
First Aid
First Aid:WASH EXPOSED AREAS WITH SOAP AND WATER.
Fire Fighting
Extinguishing Media:STANDARD FIRE EXTINGUISHER.
Fire Fighting Procedures:WEAR FACE MASK AND SCBA APPROVED BY U.S.
BUREAU OF MINES.
Unusual Fire/Explosion Hazard:NO EXPLOSIVE HAZARD.
Handling
Handling and Storage Precautions:NONE
Other Precautions:NONE.
Exposure Controls
Respiratory Protection:USE A FACE MASK.
Ventilation:USE LOCAL EXHAUST OR MECHANICAL (GENERAL) VENTILATION.
Protective Gloves:NOT NEEDED.
Eye Protection:SAFETY GLASSES
Other Protective Equipment:NONE
Work Hygienic Practices:WASH EXPOSED AREAS WITH SOAP AND WATER.
Supplemental Safety and Health
Chemical Properties
HCC:N1
NRC/State Lic Num:NONE
Spec Gravity:2.25
Solubility in Water:INSOLUBLE
Appearance and Odor:CONTINUOUS FILM OF SILICONE RUBBER ON "FIBERGLAS"
BRAID. NO ODOR.
Stability
Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZERS.
Stability Condition to Avoid:CONDITIONS ABOVE 250C WITHOUT ADEQUATE
VENTILATION.
Hazardous Decomposition Products:METHYL & PHENYL BY PRODUCTS.
Conditions to Avoid Polymerization:TEMPERATURES IN EXCESS OF 240C.
Disposal
Waste Disposal Methods:LANDFILL IS PREFERRED, BUT DISPOSAL METHOD MUST
CONFORM TO FEDERAL, STATE AND LOCAL REGULATIONS. BURNING NOT
RECOMMENDED.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.